[Mar 19, 2024] Get Free Updates Up to 365 days On Developing NSE6_FWF-6.4 Braindumps
Best Quality Fortinet NSE6_FWF-6.4 Exam Questions
NEW QUESTION # 18
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP measurements can be scheduled to occur at specific times.
- B. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- C. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- D. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
Answer: A,B
Explanation:
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION # 19
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- B. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- C. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- D. Indicates channels that cannot be used because of regulatory channel restrictions
Answer: A
NEW QUESTION # 20
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- B. Disable intra-vap-privacy for the Authors vap-wireless network
- C. Increase the transmission power of the AP radio interfaces
- D. For both interfaces in the wtp-profile, configure vap-all to be manual
Answer: A,D
NEW QUESTION # 21
What type of design model does FortiPlanner use in wireless design project?
- A. Integration model
- B. Predictive model
- C. Architectural model
- D. Analytical model
Answer: C
Explanation:
FortiPlanner will look familiar to anyone who has used architectural or home design software.
NEW QUESTION # 22
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. Two wireless APs must be sending data
- B. DTLS encryption on wireless traffic must be turned off
- C. SQL services must be running
- D. Wireless network security must be set to open
Answer: C
Explanation:
Explanation
https://docs.fortinet.com/document/fortipresence-vm/1.2.0/administration-guide/546812/introduction
NEW QUESTION # 23
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- B. Disable intra-vap-privacy for the Authors vap-wireless network
- C. Increase the transmission power of the AP radio interfaces
- D. For both interfaces in the wtp-profile, configure vap-all to be manual
Answer: A,D
Explanation:
Explanation
The configuration changes that will resolve the issue are to configure set vaps to be "Authors" for both interfaces in the wtp-profile, and to configure vap-all to be manual for both interfaces in the wtp-profile. This is because the current configuration does not assign any VAPs to the AP interfaces, which means that no wireless networks are broadcasted by the APs. The vap-all setting determines whether all VAPs are assigned to an interface or not, and the vaps setting specifies which VAPs are assigned to an interface. By setting vap-all to manual and vaps to "Authors", the APs will only broadcast the Authors wireless network on both interfaces. Disabling intra-vap-privacy for the Authors vap-wireless network will not help, as it only affects the communication between clients on the same SSID, not their connection to the AP. Increasing the transmission power of the AP radio interfaces will not help, as it only affects the signal strength and coverage of the APs, not their broadcasting of wireless networks. References: wireless-controller vap | FortiGate / FortiOS 6.4.0, Technical Note: How to configure intra-SSID privacy
NEW QUESTION # 24
Which factor is the best indicator of wireless client connection quality?
- A. Upstream link rate, the connection rate for the client to the AP
- B. The channel utilization of the channel the client is using
- C. The receive signal strength (RSS) of the client at the AP
- D. Downstream link rate, the connection rate for the AP to the client
Answer: C
Explanation:
SSI, or "Received Signal Strength Indicator," is a measurement of how well your device can hear a signal from an access point or router. It's a value that is useful for determining if you have enough signal to get a good wireless connection.
NEW QUESTION # 25
How are wireless clients assigned to a dynamic VLAN configured for hash mode?
- A. Using the current number of wireless clients connected to the SSID and the number of IPs available in the least busy VLAN
- B. Using the current number of wireless clients connected to the SSID and the group the FortiAP is a member of
- C. Using the current number of wireless clients connected to the SSID and the number of clients allocated to each of the VLANs
- D. Using the current number of wireless clients connected to the SSID and the number of VLANs available in the pool
Answer: D
Explanation:
Explanation
VLAN from the VLAN pool based on a hash of the current number of SSID clients and the number of entries in the VLAN pool.
NEW QUESTION # 26
As a network administrator, you are responsible for managing an enterprise secure wireless LAN. The controller is based in the United States, and you have been asked to deploy a number of managed APs in a remote office in Germany.
What is the correct way to ensure that the RF channels and transmission power limits are appropriately configured for the remote APs?
- A. Configure the controller for the correct country code for Germany
- B. Create a new FortiAP profile and change the county code settings on the profile
- C. Clone a suitable FortiAP profile and change the county code settings on the profile
- D. Configure the APs individually by overriding the settings in Managed FortiAPs
Answer: B
Explanation:
Explanation
The correct way to ensure that the RF channels and transmission power limits are appropriately configured for the remote APs is to create a new FortiAP profile and change the country code settings on the profile. This is because the country code settings determine the legal RF channels and transmission power limits for each country, and they are applied at the FortiAP profile level. By creating a new FortiAP profile for the remote APs, you can specify the correct country code for Germany and assign it to the APs. This will ensure that the APs comply with the local regulations and avoid interference with other devices. Configuring the APs individually by overriding the settings in Managed FortiAPs is not recommended, as it is tedious and error-prone. Configuring the controller for the correct country code for Germany is not possible, as the controller can only have one country code setting, which should match its physical location. Cloning a suitable FortiAP profile and changing the county code settings on the profile is not advisable, as it may cause conflicts with other settings that are specific to the original profile. References: Secure Wireless LAN course description, [FortiOS 6.4.0 Handbook - Wireless Controller]
NEW QUESTION # 27
Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)
- A. A VAP configured to authenticate using a radius server
- B. A VAP configured for captive portal authentication
- C. A VAP configured for WPA2 or 3 Enterprise
- D. A VAP configured to authenticate locally on FortiGate
Answer: A,C
Explanation:
Explanation
In the SSID choose WPA2-Enterprise authentication.
WSSO is RADIUS-based authentication that passes the user's user group memberships to the FortiGate.
NEW QUESTION # 28
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the AP CLI, using the cw_diag ksta command
- B. On the controller CLI, using the WiFi Client monitor
- C. On the AP CLI, using the cw_diag -d sta command
- D. On the controller CLI, using the diag wireless-controller wlac -d sta command
Answer: D
NEW QUESTION # 29
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. DHCP
- B. Static
- C. Multicast
- D. Broadcast
Answer: B
NEW QUESTION # 30
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Short message service authentication
- B. Software security token authentication
- C. Social networks authentication
- D. Hardware security token authentication
Answer: A,C
Explanation:
Explanation
According to the web search results, FortiPresence supports social networks authentication and short message service authentication as public authentication services for guest Wi-Fi access. Social networks authentication allows visitors to log in using their existing social media accounts, such as Facebook, Twitter, LinkedIn, Google, and Instagram. Short message service authentication allows visitors to receive a one-time password via SMS to their mobile phone number. These authentication methods are convenient and secure for visitors and provide valuable data for businesses. Software security token authentication and hardware security token authentication are not supported by FortiPresence as public authentication services for guest Wi-Fi access.
References: Configuring Captive Portal | FortiPresence 1.2.0, Configuring Captive Portal | FortiPresence
22.4.0
NEW QUESTION # 31
Which factor is the best indicator of wireless client connection quality?
- A. Upstream link rate, the connection rate for the client to the AP
- B. The channel utilization of the channel the client is using
- C. The receive signal strength (RSS) of the client at the AP
- D. Downstream link rate, the connection rate for the AP to the client
Answer: A
NEW QUESTION # 32
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?
- A. Security Fabric and HTTPS must be enabled on the wireless network interface
- B. The wireless network to Internet firewall policy must be configured
- C. The new network must be manually assigned to a FortiAP profile.
- D. The wireless network interface must be assigned a Layer 3 address
Answer: B
Explanation:
A FortiGate unit is an industry leading enterprise firewall. In addition to consolidating all the functions of a network firewall, IPS, anti-malware, VPN, WAN optimization, Web filtering, and application control in a single platform, FortiGate also has an integrated Wi-Fi controller.
NEW QUESTION # 33
......
Achieving the Fortinet NSE6_FWF-6.4 Certification is an excellent way for network and security professionals to demonstrate their expertise in wireless LAN security and to validate their skills and knowledge in this area. Employers can also benefit from having certified professionals on their team, as they can be assured that their wireless LANs are being managed and secured by professionals who have the necessary knowledge and skills to do so effectively.
Fortinet Exam Practice Test To Gain Brilliante Result: https://examboost.latestcram.com/NSE6_FWF-6.4-exam-cram-questions.html
